Hello,

I am getting this error message and I have finished everything it stated. Also I have downloaded software as well as drivers from hp but can’t scan with solution center.

Then I uninstalled and after that I reinstalled the software but get the same error. I am able to scan using windows scan and fax. I need a solution. I want to apply buttons on printer. Please help.

Error!

The HP imaging device was not found. Try the following steps. After each step, try scanning again.

– Turn off and then unplug the device, wait 60 seconds, and plug in and turn on the device.

Compaq Presario CQ40 smell like burning near the RAM slot inside when turn it on or even just plug Ac adaptor. Smell's burning occurs. What I did I open the where the memory bank is. So what I figured out is on the board power section.

Thus anyone knows how.

My Laptop is Compaq v3118au.

I think the integrated nv6150 overheats during use then about a minute it thermally shutdowns.

And just even watching YouTube or any videos it shutdowns and sometimes if you turn on straight after this it wont even turn on. And then sometimes when turn on and boot straight to Blue Screen of death with the message saying "Video driver failed to initialize".

Lenovo thinkcentre m58 review, how good is it?, can we use this as a home pc? infolinks vs AdSense 2012 which is better and why

Hello,

I am receiving "The application failed to initialize properly (0xc0000135)" when installing my Dell Printer 1320c. I already installed it successfully but I cannot find it anywhere on my computer. Not even in the Control Panel Add/Remove Programs. What do I need to do?

Please help me.

Mobo P5SD2-VM Asus –got chasis intruder error on staring comp. On a restarting error goes away. Only to return on starting after sometime. I have used my comp. for 3.5 years without any problem.

There is a plastic cap over chassis signal and gnd. soln. tried – cleaned Mobo. — took the battery out and placed it back. — could not find a setting in BIOS for chasis intrusion. — placed RAM in another panel. Please help. Is it pointing to a bigger problem with my Mobo.?

Hello experts

I am using Windows Xp, I installed PCI-FBUS card, NI-FBUS COMM SW for Windows v 3.2.1 and activated all the licenses as well as allowed the PCI-FBUS board in Configuration Utility. 

I received the following error message, when I opened NI-FBUS Communication Manager:

"NI-FBUS Process Startup: Fatal Error

Initialize request to Board 0 timed out, NI-FBUS may not be receiving interrupts from board.  Check your board IRQ settings with the NI-FBUS interface configuration utility.  NI-FBUS will not Exit."

But all the settings were in default.  Just NI-FBUS Communication Manager will run successfully if an H1 interface board property is keep in "Polled Mode." 

Hello expert,

Just I have loaded the LifeCam Software 3.0 and after that I got this error message when launching the Webcam,

“LifeCam.exe has encountered a problem and needs to close.  We are sorry for the inconvenience. ” 

I loaded it from a disk. Because of this error I removed this software and then downloaded it from the Microsoft Website. 

After downloading, I launched the Webcam again and I got the same error.

What is the problem?? Please help.

Thanks.

Hi all

Just I have upgraded my computer to Windows 7 from XP. But after that I have got that my Blackberry Desktop Manager will not open as a result I am not able to sync my calendar.

Recently I installed the 6.02 version of BDM. When I try to run it I find the welcome display but when I select 'get started' I find a windows error message saying that it just stopped working.

Please give me a solution. I need to solve it.

Thanks.

Hello,

Last night Just I migrated to WP 7 RTM from WP 7 Beta.

Everything was working very fine and easily I could create latest WP 7 RTM applications in VS 2010 Ultimate. Then I started making quick tests with the latest templates and easily I managed to arrange those on the Emulator.

By the way the Emulator RTM seems to be much quicker and also performing well than the Beta version. In this morning I decided to setup new Silverlight 4 Toolkit for Windows Phone 7. Now when I try to start any new WP 7 RTM application from VS 2010 Ultimate, all the time I get the similar error message:

Zune software is not launched. Retry after making sure that

Zune is launched